onlinechem.pl marine
Technical guide

Marine SCR explained: how it works and what it consumes

Selective catalytic reduction on ships — high- and low-pressure arrangements, reagent consumption, Tier III limits and the failure modes owners actually report.

Updated: 18 November 2026

SCR injects a urea solution into the exhaust ahead of a catalyst, converting nitrogen oxides into nitrogen and water. On ships the reagent is AUS 40, a 40% aqueous urea solution to ISO 18611-1. It is the principal route to IMO Tier III compliance, and typical reagent consumption is 13.5–18 g/kWh.

Where Tier III actually bites

MARPOL Annex VI regulation 13 sets NOx limits in tiers. Tier III applies inside designated emission control areas. For the Baltic and North Sea, it covers vessels with diesel engines above 130 kW whose keels were laid on or after 1 January 2021.

For slow-speed engines — below 130 rpm, which covers most large two-strokes — the Tier III limit is 3.4 g/kWh of NOx. Measured results after SCR in published studies land around 2.09–2.31 g/kWh, so a working system has margin.

This matters commercially because it defines who your customers are. Every newbuild delivered into Baltic service since 2021 with a conventional diesel above 130 kW is either on SCR or on EGR. That includes tugs, dredgers, pilot boats, crew transfer vessels and offshore support vessels, not just large tonnage.

High-pressure and low-pressure arrangements

High-pressure SCRLow-pressure SCR
Reactor positionbefore the turbochargerafter the turbocharger
Operating conditionshigher pressure and temperaturelower
Fuel penaltyroughly 0–3 g/kWh for both per WinGD; one 10 MW two-stroke study found under 1 g/kWh for HP-SCR

What the system consumes, and how to size it

Published consumption figures for Tier II to Tier III reduction cluster rather than scatter, which is a relief after the caustic soda numbers. ABS and WinGD both give around 18 g/kWh at full load. Wabtec uses 13.5 g/kWh as a stoichiometric baseline. ABS also cites about 7 g/kWh in a second place without making the case clear, so we treat 13.5–18 as the working band.

A 5 MW engine at 60% load running a full day under Tier III therefore needs roughly 1.6 to 2.2 tonnes of AUS 40 per day — call it two IBCs. Over a week that is a tanker conversation, not a pallet conversation. Our estimator does this arithmetic with the assumptions on screen.

What actually goes wrong

This is the part the brochures skip. A 2023 TNO review reported that NOx emissions from Tier III ships are higher than the legislation intended, and that owners report a substantial number of technical problems with SCR systems. The recurring failure modes:

  • Deposits in the injector and on the catalyst face, from reagent outside specification on biuret, aldehydes or insolubles.
  • Catalyst poisoning by metals and phosphate — cumulative, invisible until conversion drops.
  • Ammonia slip when dosing runs ahead of what the catalyst can convert.
  • Crystallisation in tanks and lines when heating or insulation is inadequate, which is why AUS 40 tanks are heated.
  • Operating window — the catalyst needs exhaust temperature within a band, so low-load running is its own problem.

Reagent quality does not explain all of those. It explains some of them, and it is the only one you can rule out with a document before the product reaches the tank.

Why quality is a compliance matter, not just maintenance

The same TNO work notes that monitoring can be limited to continuous urea consumption and quality in relation to fuel consumption and engine load. If quality is among the monitored quantities, then the certificate of analysis for each batch is part of the evidence chain, not a courtesy attachment.

What to have on hand before ordering

  1. Engine power under SCR treatment and typical load profile.
  2. Expected hours per day inside the Baltic or North Sea emission control area.
  3. Reagent tank capacity and whether it is heated.
  4. Your current supplier’s certificate, so there is something to compare against.

Questions we get asked

What is SCR on a ship?

Selective catalytic reduction. A urea solution is injected into the exhaust stream ahead of a catalyst, where it converts nitrogen oxides into nitrogen and water. On ships the reagent is AUS 40, a 40% aqueous urea solution to ISO 18611-1. It is the main way of meeting IMO Tier III NOx limits.

What is the difference between high-pressure and low-pressure SCR?

Position relative to the turbocharger. A high-pressure reactor sits ahead of it, working at higher pressure and temperature; a low-pressure reactor sits after it. WinGD lists a fuel penalty of roughly 0 to 3 g/kWh for both; one study of a 10 MW two-stroke engine found the fuel consumption rise with high-pressure SCR did not exceed 1 g/kWh.

Which ships have to meet Tier III?

In the Baltic and North Sea emission control areas, vessels with diesel engines above 130 kW whose keels were laid on or after 1 January 2021. The Tier III limit for slow-speed engines below 130 rpm is 3.4 g/kWh of NOx.

Is EGR an alternative to SCR?

Yes. Exhaust gas recirculation achieves Tier III compliance without a reducing agent, so an EGR vessel consumes no urea at all. Which route a ship took is decided at the design stage.

Sources

  • MARPOL Annex VI regulation 13 — NOx tiers; Baltic and North Sea NOx emission control areas for ships built from 1 January 2021.
  • Damen and Riviera Maritime Media — Tier III applies to engines above 130 kW with keel laying after 1 January 2021 in the North Sea and Baltic.
  • ABS, Advisory on NOx Tier III Compliance — about 18 g/kWh at 100% load for Tier II to Tier III reduction; a separate figure of about 7 g/kWh with an unclear basis.
  • WinGD, SCR FAQ — AUS 40 as the marine standard; average consumption about 18 g/kWh; fuel penalty up to roughly 2–3 g/kWh; HP reactor ahead of the turbocharger.
  • Wabtec — 13.5 g/kWh as a calculated stoichiometric basis for a 40% solution.
  • Study of a 10 MW two-stroke engine — BSFC rise with HP-SCR not exceeding 1 g/kWh; measured NOx 2.09 g/kWh; a low-pressure SCR study reporting 2.31 g/kWh.
  • TNO (2023) — Tier III NOx higher than intended; substantial technical issues reported; monitoring may rest on continuous urea consumption and quality.

Need the product, not just the answer?

From one IBC to a road tanker, delivered to your vessel in Polish ports, with the certificate of analysis for your batch.

  • Urea solution 40% (AUS 40)
  • Caustic soda 50% (NaOH)

Related guides

Call us Request delivery slot